8 inch ford rear end identification.

The Ford 8.8 differential ID tag attached to the differential will tell you the gear ratio, rear end style, and whether it has limited-slip. Also on the tag is an ID number, which, until 1985, included four to five letters and no numbers. Almost all 8.8s – and all post-’86 Ford rear ends – have letters and numbers.I recently put together a sort hybrid 8.8 axle for my '37 Chevy. Used a '86/'93 Mustang housing, Left side 5 lug Ranger axles on both sides, Ranger 10" brakes and LSD 3.73 gears, 59" width. Ranger housings are heavier constructed than Mustang models and Explorer are heavier still. However, the Mustang has nearly centered pinion and ...See All 20 Photos. In the early days of hot rodding, with the majority of hot rods being Fords, it stands to reason the '30s and '40s Ford "banjo" rearend dominated the scene. It's still popular ...It looks like a 9 inch, but is smaller. The 9 (and 8) inch have a solid axle housing, there is no inspection cover at the rear. The 9 (and 8) inch rear ends are known as a drop out, because the entire 3rd member (carrier aka pumpkin) comes out of the front of the housing as a unit. All the Dana's, Ford 8.8's have inspection covers, as do the ...Ford Rear Axle Assembly Identification - Page 13: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S406-B: Ford F250SD, F350SD Pickup '99: 3.73: 10.50: NL--S406-C: Excursion '00 Ford F250SD, F350SD Pickup '99-01:

This is the most sought-after 8 3/4-inch version, and is called the "489" case. The pinion shaft diameter on these rear ends was 1 7/8 inches, and these pinion shafts were either 10- or 29-spline. The increase in diameter of the pinion shaft also relates to the rear-end assembly's strength. Normally, the 741 cases were used in A-body or lighter ...See All 20 Photos. In the early days of hot rodding, with the majority of hot rods being Fords, it stands to reason the '30s and '40s Ford "banjo" rearend dominated the scene. It's still popular ...

Keep in mind as mentioned, the Fairlane spring perch distances were not the same as the Mustang. All the Galaxies I have seen from throughout the 1960's used the 9-inch rear, regardless of engine size. Axle Widths: 1965-1966 Mustang 57.25 inches. 1967-1970 Mustang 59.25 inches. 1971-1973 Mustang 61.25 inches.

The Ford 9.75" Rear End The 9.75" rear end is the old war horse of the two available rear ends for the 2015-2020 F150s. The good news is that the 9.75" is extremely distinct in how it looks, and in our experience, is the more common of the two differential options.The 9.75" has a very noticeable taper the goes toward the passenger's side of the truck on both the top and bottom of the ...When it comes to understanding the various components of a vehicle, the rear axle is often overlooked. However, for those who have a passion for off-roading or are simply intereste...Looking for 8 or 9" rear ends you should be looking at 64.5-66 Mustangs and some late 50's Fords to get the correct axle width. 67-68 will be too wide...been there, done that. My car was born a 6 cyl. It had a 289 in it when I bought it, but I had to convert everything else.Ford Rear End/Differential Identification. Hey all, does this seem like an 8 inch Ford rear end to you, because it does to me. Going to upgrade to 3.55 gears and wanted to of course make sure before I bought them. Car was originally a 6 cylinder but now has a 351W and I think the previous owner installed a beefier rear end.This means that new spring perches need to be welded on top of the Explorer's 8.8-inch axle, and they have to be spaced and angled to match your application. However, the Ford Ranger FX4 8.8-inch axle is a bolt in swap. But not all Ford Ranger FX4's have the 31-spline rear axles. From 2003-2007, ford offered (2) versions of the Ford Ranger FX4:

70XL. 3114 posts · Joined 2008. #2 · Jul 31, 2017. That is the typical WER type rear end, which is typically an 8 3/4" ring gear, but I see there was one, the WER-A, which was a 3.10:1 ratio with an 8 1/2 ring gear. Ford Rear Axle Assembly Identification - Page 01 - FORDification.com. This link has some info on Ford rear ends.

How To Install a Limited Slip/Posi Unit in a GM 10 Bolt 8.5″ Rear-end; How To Install Ring and Pinion Gears in a Ford 8.8 Rear-End; How To Narrow a Ford 8.8 Inch Rearend; How To Rebuild a GM 10 Bolt Chevy 8.5″ Rear End; How To Select Proper Rear-End / Differential Gear Ratio; Mopar Body Style Codes; Popular Automatic Transmission Dimensions

Images presented for reference and educational purposes only. To have an image removed from this website, please contact us at: [email protected]. Ford 8" Differential parts are in stock and ready to ship today at West Coast Differentials. Call our Rear-End Parts experts for LIVE help.I picked up a new 66 body that used to be a 6 cyl. but some one has converted it to a 5 lug. I want to find out what rear end it is because I am putting in a 351 windsor into it. The other question I have is that the 1966 289 mustang coupe car I am selling is set up different in the rear end. The support bars for the rear end come almost all ...Help! 9" Ford axle shaft identification. Ok thanks guys for the help thus far. Here's the deal, I've got what appears to be mix-matched axleshafts in the Heinz-57 rear axle in my '56 F100. Here's what I do know- the housing is a 67-72 housing and the backing plates/brake assemblies/drums appear to be '56 units, probably from the Dana axle.The 8.8-inch axle can be found on many different vehicles, with the Mustang being the most common. It can also be found on any of the smaller trucks with the 4.0-liter V-6 engine, such as the Explorer, Mountaineer, Ranger, and even the Aerostar. Some F-150s and Econoline vans with a V-6 engine also come with the 8.8-inch axle in the rear.Ford Rear Axle Assembly Identification - Page 04. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines. Additional Information. Ratio.Adding a 31-spline axle to a Ford 8.8 rearend means you are increasing the strength of that axle by 30 percent (19.3 + 10.7 = 30 percent increase in strength). Axles: Bigger is Better To increase ...

the center should fit in any 9" housing from 57-86. The pinion yoke and axle spline count might be different, so you do have to consider that. Also some rears had a fill plug on the housing, not the center section, so pay attention to whether or not the center chunk has a fill plug, and whether or not it needs one.2 retainers. 2 gaskets. 2 lock rings. 2 inner axle seals are optional. Fits 1957 and newer Ford 9" and Ford 8" rearends equipped with "SMALL" housing ends. If you are unsure what wheel bearings you need, please measure: Bearing ID (axle shaft journal size): 1.378". Bearing OD (housing bore diameter): 2.824". Bearing Width: 0.844".Ford 8.8 Inch. Ford 8.8 Inch Rear End Ring and Pinion Gears. We offer the most complete line of rear end parts for the Ford 8.8 inch differential, this differential was utalized by Ford as early as 1981 in the F-100 pickup, Broncos in 1981 to 1984, E150 Vans starting in 1983. Mercury's including Capri and Cugars starting in 1986.Watch this video for tips on how to mark the keys on your ring that you use the most, so you can find them easily even in the dark. Expert Advice On Improving Your Home Videos Late...For reference, the Ford car spring (PN E0AZ-4214-A) has a free height of approximately 1.510 inches and a Ford Racing truck or heavy-duty version (PN F3TZ-4214-A) is approximately 1.765 inches. The car unit was used from 1985 to 2000 while the truck version was originally used in the 1999 Cobra and all 2000-and-up V-8 Mustangs.57-59 Ranchero and station wagon 57.25 inches (narrowest 9" housing) 66-77 Bronco 58 inches but has 5-on-5 1/2 inch diameter bolt circle. 79-93 Mustang 7.5 and 8.8 57 inches. Lincoln Mark7 LSC, SVO Mustang and Fox Body Saleens use a 59.5 inch wide rear axle. 94-98 Mustangs use a 58.5 inch wide rear axle.

1948 - 1956 F1, F100 & Larger F-Series Trucks - 8.8" Ford rear axle codes - I'm sorry to do this as a search revealed this to be a common question, but I couldn't find the answer to one of the numbers. I just bought an 8.8 rear axle. It is supposed to be from a Sport Trac which means that it should be from 2000-2010....

This helpful video from the axle aces over at Currie Enterprises will show you how to determine which yoke to use in your car or truck. It discusses some of the more common yoke sizes used, and what critical U-joint measurements are involved in figuring out which yoke to choose. Whether you're building a new Ford 9 inch rear end or repairing ...Check Details Ford explorer 8.8 rear end identification. How to narrow a ford explorer 8.8 rear axle: part 2Ford 8.8 irs differential front mount bolts explorer rear diff automotive transmission Ford explorer 8.8 rear end identificationFord explorer 8.8 rear end width chart.If it has a removable cover on the rear of the axle, too bad. If it is solid in the rear and the carrier drops out of the front, you have an 8". The gear ratio should be on a tag on one of the carrier bolts. If not, roll the car forwards slowly one tire revolution and count the number of times the pinion goes around. (helps to mark it with chalk)#1 · Apr 22, 2009. I'm doing a six cylinder conversion on a 1965 Mustang. The front end components and everything is done. I purchased a rear axle and third member from …9” third members are limited-slip differentials. They are available in either a standard case, nodular case, or an aluminum thru-bolt for street to race applications. Of these Ford rear differentials, either a 28, 31, 35 or 40 spline axle can be used. All third members come with a new housing gasket, and all trac-lok units come with a ...The 9-inch ring and pinion is front-loaded into the rear end housing. First, the pinion shaft housing is removed from the front of the housing by removing five bolts. The ring and pinion are then accessed, also from the front, by removing another 10 bolts. Some of the 9-inch truck differentials will have an exaggerated hump on the rear cover to ...The ring gear in a 2.80 rear end is 7 3/4" even though its called an 8". It shouldn't be to too hard to find one in limited slip since my car came from the factory with that ratio in limited slip; its a WDJ-B. There is also a WDZ-A listed as a 2.80, limited slip but I have not seen one. Like.Ford Differentials. The Ford 8.8- and 9-inch rear differentials are two of the most popular and best-performing differentials on the market. While the 8.8-inch differential is commonly used in late-model Mustangs, the 9-inch is the more popular and arguably the most dominant high-performance differential for muscle...Ford Rear Axle Assembly Identification - Page 07: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft ... Ford Pass. '82-'83: 3.42: 8.5: L: 28-WFC-G: Capri, Mustang, Cougar 82 Fairmont, Zephyr, Granada 82 Lincoln Continental '82 Thunderbird 82: 3.08: 7.5: L: 28-When it comes to getting power to the pavement, GM's 10-bolt, 8.5-inch rear end with Positraction is a hero. Like Superman in street clothes, however, it can be hard to identify this beefy unit among its weaker cousins, the 10-bolt, 8.2-inch with open differential. GM built countless thousands of both types of 10-bolts from 1970 to 1994.

Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28-

Step 5. Count how many bolts are on the inspection cover. If you have 10 bolts, then your Ford has a 7.5-inch or an 8.8-inch rear end. If you have 12 bolts, then the rear end is a 9 inches. If you have a Ford, you can identify the size of the rear end in a matter of minutes. You do not have to take the rear end apart or drive your Ford into the ...

The hub pilot (center of the axle flange) measures 2.781" The O.D. of the axle flange measures 5.93" For more information on determining the proper axle length and the Ford 9 Inch, be sure to check out our tech articles; How to Measure and ID Differential Housings and The Rearend Debate: Ford vs. Chevy.76 posts · Joined 2013. #3 · Aug 13, 2013. 1. Recommended gear oil: GL-5 80-90 wt NON-SYNTHETIC. 2. Positractions require a Ford or Motorcraft friction modifier additive. Part number: M-19546A. This is what was recommended to me when I changed my third member. Www.justrearends.com.Just punch in 9 inch ford diff info and they will come up.the 31 splin is most of the time trucks, they put a few in cars but it was only in the high perfomance ones like boss's. ... Ford 9" rear end identification? I pulled the axles and opened the rear end. The axles are definitely 31-spline. The 3rd member has "C7AWE 41" cast inside it. Also ...A. adgdghr123 Discussion starter. 1426 posts · Joined 2002. #1 · Dec 16, 2004. What are the rear axle ratio codes for a '67? I ask because I was thinking of changing gears in the rear-end in my '68 (8" I believe), but it occurred to me today that at my local junkyard there is a '67 Galaxie with a 390. I'd imagine with a 390 it probably has a ...We decided to replace our '85 GT's weak 7.5-inch rear axle with a stronger 8.8-inch axle out of a 1989 Mustang. Since it would be upgraded with new stuff from Eaton, Superior Axle, and Ratech, we gutted the axle, had the housing sandblasted, then painted it black. Before we began reassembly, we took the 8.8 to the local car wash and cleaned it ...1965 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 6: 2.80 open differential: F: 2.80 locking differential: 2: 2.83 open differential: B: 2.83 locking differential: 1:Duke351C4V. 232 posts · Joined 2010. #9 · Feb 21, 2011. If the car's still there the door tag next to last digit/letter should indicate axle code. H would be the 2.91. Casting number C0AW: C = 60's, 0 = 1960, A = Galexie, W = Axle dept. The single horizontal rib in the picture suggests 9" standard carrier. Steve.This is just a simple video part of the ls Swap Jeep Ford 8.8 axle build showing what the axle tag means.If you’re a car enthusiast or work in the automotive industry, you know how important it is to be able to identify different parts and components of a vehicle. Before we delve into...How to Measure Ford Rear End Axle Splines, Flange Width and Height Metro Auto Parts Market: Ford Rear End Catalog: Hot to Select Axle & Measure the Companion Flange ... Therefore, the only foolproof way is to remove the axle and count. Note all 8 inch units use 28 spline axles. 28 Spline Axle: 31 Spline Axle: Note the concave oval area in ...

Ford Rear Axle Assembly Identification - Page 01 - FORDification.com San Jose 65 Coupe/EECIV EFI 5.0/T5/3.25 Currie LSD 8"/Several Mustang Steve products/Vi-King coil overs 350# ReplyThe BOM stamp (2) or Axle Identification Tags (2A) are used to identify Dana axles / differentials. The BOM will identify the model number, the gear ratio, the type of axle / differential, and component parts. Traditional BOMs are 6 digits followed by 1 or 2 digits, and start with the numbers 60 or 61. On some tags, the first 2 digits won't ...The 8" and 9" share the same axle lengths, so a '66 with a 9" would be the same axle length. Save Share. Like. 6. 66Racer Discussion starter ... Ford Muscle Cars Tech Forum. 951.9K posts 72.6K members Since 2001 A forum community dedicated to Ford performance owners and enthusiasts. Come join the discussion about popular models such as the ...Instagram:https://instagram. stardew valley kegreading eagle sunday obituariesretirement party cakes ideamcpherson obituaries delaware 1948 - 1956 F1, F100 & Larger F-Series Trucks - 8.8" Ford rear axle codes - I'm sorry to do this as a search revealed this to be a common question, but I couldn't find the answer to one of the numbers. I just bought an 8.8 rear axle. It is supposed to be from a Sport Trac which means that it should be from 2000-2010.... songfinch promo codedj akademiks height and weight Ford Explorer 8.8 inch swap into a 65/66 Mustang. I am going to be building an 8.8 inch rear end for my 66 Mustang. I have read plenty of stuff on narrowing he Explorer rear end but I have yet to hear from someone that has done it. The 8.8 is found in Rangers and Explorers most commonly but the Explorer rear end is more sought after as it is a ...Pinion Yoke and ABS Plug. 8) These rearends generally use a 28-spline pinion yoke, but some trucks use a 30-spline. 9) This is the plug for ABS found on some 8.8s. Advertisement. The Ford 8.8... tufts nutrition chart Pigiron. 189 posts · Joined 2001. #7 · Dec 26, 2001. BobbyD, The narrowest 8" is from the Mavericks at 56 1/2" and the spring pads are 43" center to center. The narrowest 9" is 57-9 Ford Rancheros and station wagons at 57 1/4" and spring pads at 43". These are almost a direct bolt in for the 49-50 Fords, about a half inch off for the spring pads.from waiting for the swamp to drain. all 8" ford rears have small wheel bearings. wheel bearing rw207ccra. axle seal 13700. pinion seal 18100. 36-3window, Jan 19, 2010. SHARE POST #3.